Get Back into Your Home Servers with an Inbound VPN on the Start9 Router
One of the benefits of running your own servers at home is control over your own data. Nextcloud for files, Immich for photos and videos, a Bitcoin node, and a whole range of other apps, without handing that to somebody else's cloud. The problem shows up when you leave the house. It all works on the home network, and then your phone on cellular data, or on some other Wi-Fi, cannot reach any of it.
Tor on Start9 or Umbrel can get you back in, but it is limited. A lot of these apps do not behave well through Tor, and every device needs Tor running just to reach the server. The other path is exposing each service on the public internet, and that is not something I want to do for security reasons.
An inbound VPN sits in the middle. This guide is the next piece of the Start9 router series. I set up WireGuard on StartWRT, connect my phone from cellular data, and open my Start9 and Umbrel servers the same way I would on home Wi-Fi. Immich still backs up photos while I am away. Those services stay off the public internet.
Check that your internet can accept the tunnel
Before any of this works, look at the type of internet you have. Satellite, some cellular home connections, and a fair number of fiber and cable plans sit behind CGNAT. The router does not have a public address of its own, so a phone on the outside cannot knock on it.
- Open whatismyip.com. It shows the public IPv4 the rest of the internet sees.
- On the router, open
router.lan, go to WAN settings, and compare that address.
They should match. If you are behind CGNAT, the router shows a 100. address and it will not match the site. The fix is a service like StartTunnel, which is a virtual private router you connect to and pay for, or a call to the ISP about the connection they gave you, or a different provider. My connection matched, so I kept going.
1. Create the inbound VPN
On the Start9 router, open Points of Entry, then Inbound VPNs, and press Add.
- Label it. I called mine server access.
- Pick the endpoint. I used the WAN IPv4.
- Attach it to a security profile. I used the home profile, so a connected phone can see the devices that live there.
- Leave the port as it is.
- Press Add VPN.
That creates the WireGuard service on the router. Next it needs a client.
2. Add the phone and choose full tunnel
Add a client and name it. I called mine my phone. You get two routing choices.
- Split traffic only sends the phone through the tunnel when it is trying to reach something on the home network. The rest of the phone's internet stays on whatever network you are using.
- Full traffic sends all of the phone's traffic through the router. The phone then has access to the other devices on that home security profile, and its normal browsing also leaves from the house.
I picked full tunnel and saved. StartWRT gives you a WireGuard file and a QR code for that device.
3. Import it into WireGuard on the phone
Install WireGuard from the Play Store, or the App Store on an iPhone. Open it, tap the plus button, and import from a file or archive. Turn the tunnel on.
Then turn the phone's Wi-Fi off so it is on cellular data only. You are on a different network, and the phone is still reaching the home profile because WireGuard is coming inbound through the router.
.local names did not resolve for me. umbrel.local and my Start9 .local name failed over WireGuard. The LAN IP addresses of those servers worked. Use the IP until mDNS behaves over the tunnel. If you have a fix for that, I want to hear it.
4. Open the servers and back up photos
Type the IP of the Start9 server and the login page comes up. Same for Umbrel. Put the password in and you are on the server. Umbrel treats the phone as if it were on the home network, because that is what the inbound VPN did. Immich, local apps, the Bitcoin node, whatever you run there, is available while you are away.
I use Immich on Umbrel as my photo and video backup. The phone had been pointed at umbrel.local plus the port. Because that name does not resolve over WireGuard, I signed out and created the endpoint with the Umbrel IP and the same port, then logged in again.
I took a photo of my keyboard on the phone, on cellular, with WireGuard on. It showed up in Immich. That is the backup working from outside the house. Traveling, I turn WireGuard on and the phone syncs to the server at home.
Clients, outbound VPN, and split tunnel
Back under Inbound VPNs, the three dots on that server let you disable it, or open Manage clients and add a laptop, another phone, or someone you actually want on the network. Each device gets its own WireGuard config, and you can revoke one device without opening the door for everyone else.
You can also put an outbound VPN on the same home profile. The phone connects with WireGuard, the router receives that traffic, and then sends it out through the VPN. A phone only holds one VPN at a time. If it is already on this WireGuard tunnel, it cannot also be connected to Obscura. Routing the outbound hop on the router covers both: you are on the home network, and your internet still leaves through the VPN.
Full tunnel is what I used in the video, so all of the phone's internet goes through the house. Split tunnel is the other setting: only traffic meant for the home network uses the VPN, and everything else uses the network you are actually on.
You do not have to publish the Start9, the Umbrel, a NAS, or any other home server on the internet to use them remotely. You also do not need Tailscale for this once the Start9 router is doing the inbound VPN itself.
Get the router: The Wi-Fi model is at store.start9.com. Code BNC5 takes 5% off, and the link is in the video description. The earlier videos in this series are the first setup and the guest outbound VPN.
Want a hand with remote access to your node?
I do private one-on-one sessions for Bitcoin security and digital security. Reach me through pathtobitcoin.xyz.
Book a 1:1 Coaching SessionWatch the Video Walkthrough
CGNAT check, the inbound VPN, the phone on cellular data, and an Immich backup landing on Umbrel.